Added BLTouch configuration to example BTT configuration.

2 files changed, 14 insertions, 14 deletions

diff --git a/marlinfw-skr-e3-mini-v2/config-2.0.9.2/Configuration.h b/marlinfw-skr-e3-mini-v2/config-2.0.9.2/Configuration.h
index 4bdc3da..2d06579 100644
--- a/marlinfw-skr-e3-mini-v2/config-2.0.9.2/Configuration.h
+++ b/marlinfw-skr-e3-mini-v2/config-2.0.9.2/Configuration.h
@@ -1090,7 +1090,7 @@
 /**
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
-//#define BLTOUCH
+#define BLTOUCH
 
 /**
  * Touch-MI Probe by hotends.fr
@@ -1182,11 +1182,11 @@
  *     |    [-]    |
  *     O-- FRONT --+
  */
-#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
+#define NOZZLE_TO_PROBE_OFFSET { -43, -10, 0 } // Z-offset usally -2.58
 
 // Most probes should stay away from the edges of the bed, but
 // with NOZZLE_AS_PROBE this can be negative for a wider probing area.
-#define PROBING_MARGIN 10
+#define PROBING_MARGIN 40
 
 // X and Y axis travel speed (mm/min) between probes
 #define XY_PROBE_FEEDRATE (133*60)
@@ -1233,7 +1233,7 @@
  * A total of 2 does fast/slow probes with a weighted average.
  * A total of 3 or more adds more slow probes, taking the average.
  */
-//#define MULTIPLE_PROBING 2
+#define MULTIPLE_PROBING 2
 //#define EXTRA_PROBING    1
 
 /**
@@ -1539,9 +1539,9 @@
  */
 //#define AUTO_BED_LEVELING_3POINT
 //#define AUTO_BED_LEVELING_LINEAR
-//#define AUTO_BED_LEVELING_BILINEAR
+#define AUTO_BED_LEVELING_BILINEAR
 //#define AUTO_BED_LEVELING_UBL
-#define MESH_BED_LEVELING
+//#define MESH_BED_LEVELING
 
 /**
  * Normally G28 leaves leveling disabled on completion. Enable one of
@@ -1606,7 +1606,7 @@
 #if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
 
   // Set the number of grid points per dimension.
-  #define GRID_MAX_POINTS_X 5
+  #define GRID_MAX_POINTS_X 9
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
 
   // Probe along the Y axis, advancing X after each column
@@ -1740,7 +1740,7 @@
  * - Allows Z homing only when XY positions are known and trusted.
  * - If stepper drivers sleep, XY homing may be required again before Z homing.
  */
-//#define Z_SAFE_HOMING
+#define Z_SAFE_HOMING
 
 #if ENABLED(Z_SAFE_HOMING)
   #define Z_SAFE_HOMING_X_POINT X_CENTER  // X point for Z homing
diff --git a/marlinfw-skr-e3-mini-v2/config-2.0.9.2/Configuration_adv.h b/marlinfw-skr-e3-mini-v2/config-2.0.9.2/Configuration_adv.h
index 4c9224c..5227362 100644
--- a/marlinfw-skr-e3-mini-v2/config-2.0.9.2/Configuration_adv.h
+++ b/marlinfw-skr-e3-mini-v2/config-2.0.9.2/Configuration_adv.h
@@ -818,7 +818,7 @@
 
   // Safety: The probe needs time to recognize the command.
   //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
+  #define BLTOUCH_DELAY 500
 
   /**
    * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
@@ -826,7 +826,7 @@
 
   // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
   //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
+  #define BLTOUCH_FORCE_SW_MODE
 
   /**
    * Settings for BLTouch Smart 3.0 and 3.1
@@ -1225,14 +1225,14 @@
 
   // Add Probe Z Offset calibration to the Z Probe Offsets menu
   #if HAS_BED_PROBE
-    //#define PROBE_OFFSET_WIZARD
+    #define PROBE_OFFSET_WIZARD
     #if ENABLED(PROBE_OFFSET_WIZARD)
       //
       // Enable to init the Probe Z-Offset when starting the Wizard.
       // Use a height slightly above the estimated nozzle-to-probe Z offset.
       // For example, with an offset of -5, consider a starting height of -4.
       //
-      //#define PROBE_OFFSET_WIZARD_START_Z -4.0
+      #define PROBE_OFFSET_WIZARD_START_Z -2.0
 
       // Set a convenient position to do the calibration (probing point and nozzle/bed-distance)
       //#define PROBE_OFFSET_WIZARD_XY_POS { X_CENTER, Y_CENTER }
@@ -1883,9 +1883,9 @@
     #endif
   #endif
 
-  //#define BABYSTEP_DISPLAY_TOTAL          // Display total babysteps since last G28
+  #define BABYSTEP_DISPLAY_TOTAL          // Display total babysteps since last G28
 
-  //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
+  #define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets
     //#define BABYSTEP_ZPROBE_GFX_OVERLAY   // Enable graphical overlay on Z-offset editor