Added 1.1.x for CR10S, from 1.1.9

1 files changed, 1930 insertions, 0 deletions

diff --git a/marlinfw/config-1.1.x/Configuration.h b/marlinfw/config-1.1.x/Configuration.h
new file mode 100644
index 0000000..37b4c2a
--- /dev/null
+++ b/marlinfw/config-1.1.x/Configuration.h
@@ -0,0 +1,1930 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration.h
+ *
+ * Basic settings such as:
+ *
+ * - Type of electronics
+ * - Type of temperature sensor
+ * - Printer geometry
+ * - Endstop configuration
+ * - LCD controller
+ * - Extra features
+ *
+ * Advanced settings can be found in Configuration_adv.h
+ *
+ */
+#ifndef CONFIGURATION_H
+#define CONFIGURATION_H
+#define CONFIGURATION_H_VERSION 010109
+
+//===========================================================================
+//============================= Getting Started =============================
+//===========================================================================
+
+/**
+ * Here are some standard links for getting your machine calibrated:
+ *
+ * http://reprap.org/wiki/Calibration
+ * http://youtu.be/wAL9d7FgInk
+ * http://calculator.josefprusa.cz
+ * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
+ * http://www.thingiverse.com/thing:5573
+ * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
+ * http://www.thingiverse.com/thing:298812
+ */
+
+//===========================================================================
+//============================= DELTA Printer ===============================
+//===========================================================================
+// For a Delta printer start with one of the configuration files in the
+// example_configurations/delta directory and customize for your machine.
+//
+
+//===========================================================================
+//============================= SCARA Printer ===============================
+//===========================================================================
+// For a SCARA printer start with the configuration files in
+// example_configurations/SCARA and customize for your machine.
+//
+
+//===========================================================================
+//============================= HANGPRINTER =================================
+//===========================================================================
+// For a Hangprinter start with the configuration file in the
+// example_configurations/hangprinter directory and customize for your machine.
+//
+
+// @section info
+
+// User-specified version info of this build to display in [Pronterface, etc] terminal window during
+// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
+// build by the user have been successfully uploaded into firmware.
+#define STRING_CONFIG_H_AUTHOR "(printedsolid.com, CR-10S)" // Who made the changes.
+#define SHOW_BOOTSCREEN
+#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
+#define STRING_SPLASH_LINE2 WEBSITE_URL         // will be shown during bootup in line 2
+
+/**
+ * *** VENDORS PLEASE READ ***
+ *
+ * Marlin allows you to add a custom boot image for Graphical LCDs.
+ * With this option Marlin will first show your custom screen followed
+ * by the standard Marlin logo with version number and web URL.
+ *
+ * We encourage you to take advantage of this new feature and we also
+ * respectfully request that you retain the unmodified Marlin boot screen.
+ */
+
+// Enable to show the bitmap in Marlin/_Bootscreen.h on startup.
+//#define SHOW_CUSTOM_BOOTSCREEN
+
+// Enable to show the bitmap in Marlin/_Statusscreen.h on the status screen.
+#define CUSTOM_STATUS_SCREEN_IMAGE
+
+// @section machine
+
+/**
+ * Select the serial port on the board to use for communication with the host.
+ * This allows the connection of wireless adapters (for instance) to non-default port pins.
+ * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
+ *
+ * :[0, 1, 2, 3, 4, 5, 6, 7]
+ */
+#define SERIAL_PORT 0
+
+/**
+ * This setting determines the communication speed of the printer.
+ *
+ * 250000 works in most cases, but you might try a lower speed if
+ * you commonly experience drop-outs during host printing.
+ * You may try up to 1000000 to speed up SD file transfer.
+ *
+ * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
+ */
+#define BAUDRATE 115200
+
+// Enable the Bluetooth serial interface on AT90USB devices
+//#define BLUETOOTH
+
+// The following define selects which electronics board you have.
+// Please choose the name from boards.h that matches your setup
+#ifndef MOTHERBOARD
+  #define MOTHERBOARD BOARD_RAMPS_14_EFB
+  #define PIN_EXP1 65 // A11
+  #define PIN_EXP2 66 // A12
+  #define PIN_EXP3 11 // SERVO0_PIN
+  #define PIN_EXP4 12 // PS_ON_PIN
+#endif
+
+// Optional custom name for your RepStrap or other custom machine
+// Displayed in the LCD "Ready" message
+#define CUSTOM_MACHINE_NAME "CR-10S"
+
+// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
+// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
+//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
+
+// @section extruder
+
+// This defines the number of extruders
+// :[1, 2, 3, 4, 5]
+#define EXTRUDERS 1
+
+// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
+#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
+
+// For Cyclops or any "multi-extruder" that shares a single nozzle.
+//#define SINGLENOZZLE
+
+/**
+ * Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants.
+ *
+ * This device allows one stepper driver on a control board to drive
+ * two to eight stepper motors, one at a time, in a manner suitable
+ * for extruders.
+ *
+ * This option only allows the multiplexer to switch on tool-change.
+ * Additional options to configure custom E moves are pending.
+ */
+//#define MK2_MULTIPLEXER
+#if ENABLED(MK2_MULTIPLEXER)
+  // Override the default DIO selector pins here, if needed.
+  // Some pins files may provide defaults for these pins.
+  //#define E_MUX0_PIN 40  // Always Required
+  //#define E_MUX1_PIN 42  // Needed for 3 to 8 steppers
+  //#define E_MUX2_PIN 44  // Needed for 5 to 8 steppers
+#endif
+
+// A dual extruder that uses a single stepper motor
+//#define SWITCHING_EXTRUDER
+#if ENABLED(SWITCHING_EXTRUDER)
+  #define SWITCHING_EXTRUDER_SERVO_NR 0
+  #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3]
+  #if EXTRUDERS > 3
+    #define SWITCHING_EXTRUDER_E23_SERVO_NR 1
+  #endif
+#endif
+
+// A dual-nozzle that uses a servomotor to raise/lower one of the nozzles
+//#define SWITCHING_NOZZLE
+#if ENABLED(SWITCHING_NOZZLE)
+  #define SWITCHING_NOZZLE_SERVO_NR 0
+  #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 }   // Angles for E0, E1
+  //#define HOTEND_OFFSET_Z { 0.0, 0.0 }
+#endif
+
+/**
+ * Two separate X-carriages with extruders that connect to a moving part
+ * via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
+ */
+//#define PARKING_EXTRUDER
+#if ENABLED(PARKING_EXTRUDER)
+  #define PARKING_EXTRUDER_SOLENOIDS_INVERT           // If enabled, the solenoid is NOT magnetized with applied voltage
+  #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW  // LOW or HIGH pin signal energizes the coil
+  #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250        // Delay (ms) for magnetic field. No delay if 0 or not defined.
+  #define PARKING_EXTRUDER_PARKING_X { -78, 184 }     // X positions for parking the extruders
+  #define PARKING_EXTRUDER_GRAB_DISTANCE 1            // mm to move beyond the parking point to grab the extruder
+  #define PARKING_EXTRUDER_SECURITY_RAISE 5           // Z-raise before parking
+  #define HOTEND_OFFSET_Z { 0.0, 1.3 }                // Z-offsets of the two hotends. The first must be 0.
+#endif
+
+/**
+ * "Mixing Extruder"
+ *   - Adds G-codes M163 and M164 to set and "commit" the current mix factors.
+ *   - Extends the stepping routines to move multiple steppers in proportion to the mix.
+ *   - Optional support for Repetier Firmware's 'M164 S<index>' supporting virtual tools.
+ *   - This implementation supports up to two mixing extruders.
+ *   - Enable DIRECT_MIXING_IN_G1 for M165 and mixing in G1 (from Pia Taubert's reference implementation).
+ */
+//#define MIXING_EXTRUDER
+#if ENABLED(MIXING_EXTRUDER)
+  #define MIXING_STEPPERS 2        // Number of steppers in your mixing extruder
+  #define MIXING_VIRTUAL_TOOLS 16  // Use the Virtual Tool method with M163 and M164
+  //#define DIRECT_MIXING_IN_G1    // Allow ABCDHI mix factors in G1 movement commands
+#endif
+
+// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
+// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
+// For the other hotends it is their distance from the extruder 0 hotend.
+//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
+//#define HOTEND_OFFSET_Y {0.0, 5.00}  // (in mm) for each extruder, offset of the hotend on the Y axis
+
+// @section machine
+
+/**
+ * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ *
+ * 0 = No Power Switch
+ * 1 = ATX
+ * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
+ *
+ * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ */
+#define POWER_SUPPLY 0
+
+#if POWER_SUPPLY > 0
+  // Enable this option to leave the PSU off at startup.
+  // Power to steppers and heaters will need to be turned on with M80.
+  //#define PS_DEFAULT_OFF
+
+  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  #if ENABLED(AUTO_POWER_CONTROL)
+    #define AUTO_POWER_FANS           // Turn on PSU if fans need power
+    #define AUTO_POWER_E_FANS
+    #define AUTO_POWER_CONTROLLERFAN
+    #define POWER_TIMEOUT 30
+  #endif
+
+#endif
+
+// @section temperature
+
+//===========================================================================
+//============================= Thermal Settings ============================
+//===========================================================================
+
+/**
+ * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+ *
+ * Temperature sensors available:
+ *
+ *    -4 : thermocouple with AD8495
+ *    -3 : thermocouple with MAX31855 (only for sensor 0)
+ *    -2 : thermocouple with MAX6675 (only for sensor 0)
+ *    -1 : thermocouple with AD595
+ *     0 : not used
+ *     1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
+ *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
+ *     3 : Mendel-parts thermistor (4.7k pullup)
+ *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
+ *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup)
+ *   501 : 100K Zonestar (Tronxy X3A) Thermistor
+ *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
+ *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
+ *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
+ *     8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
+ *     9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
+ *    10 : 100k RS thermistor 198-961 (4.7k pullup)
+ *    11 : 100k beta 3950 1% thermistor (4.7k pullup)
+ *    12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
+ *    13 : 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
+ *    15 : 100k thermistor calibration for JGAurora A5 hotend
+ *    20 : the PT100 circuit found in the Ultimainboard V2.x
+ *    60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
+ *    66 : 4.7M High Temperature thermistor from Dyze Design
+ *    70 : the 100K thermistor found in the bq Hephestos 2
+ *    75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor
+ *
+ *       1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k.
+ *                              (but gives greater accuracy and more stable PID)
+ *    51 : 100k thermistor - EPCOS (1k pullup)
+ *    52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
+ *    55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
+ *
+ *  1047 : Pt1000 with 4k7 pullup
+ *  1010 : Pt1000 with 1k pullup (non standard)
+ *   147 : Pt100 with 4k7 pullup
+ *   110 : Pt100 with 1k pullup (non standard)
+ *
+ *         Use these for Testing or Development purposes. NEVER for production machine.
+ *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
+ *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
+ *
+ * :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950  1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '66':"Dyze Design 4.7M High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" }
+ */
+#define TEMP_SENSOR_0 1
+#define TEMP_SENSOR_1 0
+#define TEMP_SENSOR_2 0
+#define TEMP_SENSOR_3 0
+#define TEMP_SENSOR_4 0
+#define TEMP_SENSOR_BED 1
+#define TEMP_SENSOR_CHAMBER 0
+
+// Dummy thermistor constant temperature readings, for use with 998 and 999
+#define DUMMY_THERMISTOR_998_VALUE 25
+#define DUMMY_THERMISTOR_999_VALUE 100
+
+// Use temp sensor 1 as a redundant sensor with sensor 0. If the readings
+// from the two sensors differ too much the print will be aborted.
+//#define TEMP_SENSOR_1_AS_REDUNDANT
+#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
+
+// Extruder temperature must be close to target for this long before M109 returns success
+#define TEMP_RESIDENCY_TIME 10  // (seconds)
+#define TEMP_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 10  // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
+// The minimal temperature defines the temperature below which the heater will not be enabled It is used
+// to check that the wiring to the thermistor is not broken.
+// Otherwise this would lead to the heater being powered on all the time.
+#define HEATER_0_MINTEMP 5
+#define HEATER_1_MINTEMP 5
+#define HEATER_2_MINTEMP 5
+#define HEATER_3_MINTEMP 5
+#define HEATER_4_MINTEMP 5
+#define BED_MINTEMP      5
+
+// When temperature exceeds max temp, your heater will be switched off.
+// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
+// You should use MINTEMP for thermistor short/failure protection.
+#define HEATER_0_MAXTEMP 250
+#define HEATER_1_MAXTEMP 275
+#define HEATER_2_MAXTEMP 275
+#define HEATER_3_MAXTEMP 275
+#define HEATER_4_MAXTEMP 275
+#define BED_MAXTEMP      120
+
+//===========================================================================
+//============================= PID Settings ================================
+//===========================================================================
+// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
+
+// Comment the following line to disable PID and enable bang-bang.
+#define PIDTEMP
+#define BANG_MAX 255     // Limits current to nozzle while in bang-bang mode; 255=full current
+#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#define PID_K1 0.95      // Smoothing factor within any PID loop
+#if ENABLED(PIDTEMP)
+  //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
+  //#define PID_DEBUG // Sends debug data to the serial port.
+  //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
+  //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
+  //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
+                                  // Set/get with gcode: M301 E[extruder number, 0-2]
+  #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
+                                  // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+
+  // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
+
+  // Ultimaker
+  #define DEFAULT_Kp 22.2
+  #define DEFAULT_Ki 1.08
+  #define DEFAULT_Kd 114
+
+  // MakerGear
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
+
+  // Mendel Parts V9 on 12V
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
+
+#endif // PIDTEMP
+
+//===========================================================================
+//============================= PID > Bed Temperature Control ===============
+//===========================================================================
+
+/**
+ * PID Bed Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use bed PID until someone else verifies that your hardware works.
+ */
+//#define PIDTEMPBED
+
+//#define BED_LIMIT_SWITCHING
+
+/**
+ * Max Bed Power
+ * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the bed that acts like a divider
+ * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED)
+ */
+#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
+
+#if ENABLED(PIDTEMPBED)
+
+  //#define PID_BED_DEBUG // Sends debug data to the serial port.
+
+  //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
+  //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
+  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKd 305.4
+
+  //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
+  //from pidautotune
+  //#define DEFAULT_bedKp 97.1
+  //#define DEFAULT_bedKi 1.41
+  //#define DEFAULT_bedKd 1675.16
+
+  // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
+#endif // PIDTEMPBED
+
+// @section extruder
+
+/**
+ * Prevent extrusion if the temperature is below EXTRUDE_MINTEMP.
+ * Add M302 to set the minimum extrusion temperature and/or turn
+ * cold extrusion prevention on and off.
+ *
+ * *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! ***
+ */
+#define PREVENT_COLD_EXTRUSION
+#define EXTRUDE_MINTEMP 170
+
+/**
+ * Prevent a single extrusion longer than EXTRUDE_MAXLENGTH.
+ * Note: For Bowden Extruders make this large enough to allow load/unload.
+ */
+#define PREVENT_LENGTHY_EXTRUDE
+#define EXTRUDE_MAXLENGTH 435
+
+//===========================================================================
+//======================== Thermal Runaway Protection =======================
+//===========================================================================
+
+/**
+ * Thermal Protection provides additional protection to your printer from damage
+ * and fire. Marlin always includes safe min and max temperature ranges which
+ * protect against a broken or disconnected thermistor wire.
+ *
+ * The issue: If a thermistor falls out, it will report the much lower
+ * temperature of the air in the room, and the the firmware will keep
+ * the heater on.
+ *
+ * If you get "Thermal Runaway" or "Heating failed" errors the
+ * details can be tuned in Configuration_adv.h
+ */
+
+#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
+#define THERMAL_PROTECTION_BED     // Enable thermal protection for the heated bed
+
+//===========================================================================
+//============================= Mechanical Settings =========================
+//===========================================================================
+
+// @section machine
+
+// Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics
+// either in the usual order or reversed
+//#define COREXY
+//#define COREXZ
+//#define COREYZ
+//#define COREYX
+//#define COREZX
+//#define COREZY
+
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
+// @section homing
+
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+//#define USE_ZMAX_PLUG
+
+// Enable pullup for all endstops to prevent a floating state
+#define ENDSTOPPULLUPS
+#if DISABLED(ENDSTOPPULLUPS)
+  // Disable ENDSTOPPULLUPS to set pullups individually
+  //#define ENDSTOPPULLUP_XMAX
+  //#define ENDSTOPPULLUP_YMAX
+  //#define ENDSTOPPULLUP_ZMAX
+  //#define ENDSTOPPULLUP_XMIN
+  //#define ENDSTOPPULLUP_YMIN
+  //#define ENDSTOPPULLUP_ZMIN
+  //#define ENDSTOPPULLUP_ZMIN_PROBE
+#endif
+
+// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
+#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
+
+/**
+ * Stepper Drivers
+ *
+ * These settings allow Marlin to tune stepper driver timing and enable advanced options for
+ * stepper drivers that support them. You may also override timing options in Configuration_adv.h.
+ *
+ * A4988 is assumed for unspecified drivers.
+ *
+ * Options: A4988, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE
+ * :['A4988', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE']
+ */
+//#define X_DRIVER_TYPE  A4988
+//#define Y_DRIVER_TYPE  A4988
+//#define Z_DRIVER_TYPE  A4988
+//#define X2_DRIVER_TYPE A4988
+//#define Y2_DRIVER_TYPE A4988
+//#define Z2_DRIVER_TYPE A4988
+//#define E0_DRIVER_TYPE A4988
+//#define E1_DRIVER_TYPE A4988
+//#define E2_DRIVER_TYPE A4988
+//#define E3_DRIVER_TYPE A4988
+//#define E4_DRIVER_TYPE A4988
+
+// Enable this feature if all enabled endstop pins are interrupt-capable.
+// This will remove the need to poll the interrupt pins, saving many CPU cycles.
+//#define ENDSTOP_INTERRUPTS_FEATURE
+
+/**
+ * Endstop Noise Filter
+ *
+ * Enable this option if endstops falsely trigger due to noise.
+ * NOTE: Enabling this feature means adds an error of +/-0.2mm, so homing
+ * will end up at a slightly different position on each G28. This will also
+ * reduce accuracy of some bed probes.
+ * For mechanical switches, the better approach to reduce noise is to install
+ * a 100 nanofarads ceramic capacitor in parallel with the switch, making it
+ * essentially noise-proof without sacrificing accuracy.
+ * This option also increases MCU load when endstops or the probe are enabled.
+ * So this is not recommended. USE AT YOUR OWN RISK.
+ * (This feature is not required for common micro-switches mounted on PCBs
+ * based on the Makerbot design, since they already include the 100nF capacitor.)
+ */
+//#define ENDSTOP_NOISE_FILTER
+
+//=============================================================================
+//============================== Movement Settings ============================
+//=============================================================================
+// @section motion
+
+/**
+ * Default Settings
+ *
+ * These settings can be reset by M502
+ *
+ * Note that if EEPROM is enabled, saved values will override these.
+ */
+
+/**
+ * With this option each E stepper can have its own factors for the
+ * following movement settings. If fewer factors are given than the
+ * total number of extruders, the last value applies to the rest.
+ */
+//#define DISTINCT_E_FACTORS
+
+/**
+ * Default Axis Steps Per Unit (steps/mm)
+ * Override with M92
+ *                                      X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
+ */
+#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 400, 95 }
+
+/**
+ * Default Max Feed Rate (mm/s)
+ * Override with M203
+ *                                      X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
+ */
+#define DEFAULT_MAX_FEEDRATE          { 2500, 2500, 100, 25 }
+
+/**
+ * Default Max Acceleration (change/s) change = mm/s
+ * (Maximum start speed for accelerated moves)
+ * Override with M201
+ *                                      X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
+ */
+#define DEFAULT_MAX_ACCELERATION      { 500, 500, 100, 10000 }
+
+/**
+ * Default Acceleration (change/s) change = mm/s
+ * Override with M204
+ *
+ *   M204 P    Acceleration
+ *   M204 R    Retract Acceleration
+ *   M204 T    Travel Acceleration
+ */
+#define DEFAULT_ACCELERATION          575    // X, Y, Z and E acceleration for printing moves
+#define DEFAULT_RETRACT_ACCELERATION  1000    // E acceleration for retracts
+#define DEFAULT_TRAVEL_ACCELERATION   1000    // X, Y, Z acceleration for travel (non printing) moves
+
+/**
+ * Default Jerk (mm/s)
+ * Override with M205 X Y Z E
+ *
+ * "Jerk" specifies the minimum speed change that requires acceleration.
+ * When changing speed and direction, if the difference is less than the
+ * value set here, it may happen instantaneously.
+ */
+#define DEFAULT_XJERK                 20.0
+#define DEFAULT_YJERK                 20.0
+#define DEFAULT_ZJERK                  0.4
+#define DEFAULT_EJERK                  5.0
+
+/**
+ * S-Curve Acceleration
+ *
+ * This option eliminates vibration during printing by fitting a Bézier
+ * curve to move acceleration, producing much smoother direction changes.
+ *
+ * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
+ */
+//#define S_CURVE_ACCELERATION
+
+//===========================================================================
+//============================= Z Probe Options =============================
+//===========================================================================
+// @section probes
+
+//
+// See http://marlinfw.org/docs/configuration/probes.html
+//
+
+/**
+ * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
+ *
+ * Enable this option for a probe connected to the Z Min endstop pin.
+ */
+#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
+
+/**
+ * Z_MIN_PROBE_ENDSTOP
+ *
+ * Enable this option for a probe connected to any pin except Z-Min.
+ * (By default Marlin assumes the Z-Max endstop pin.)
+ * To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below.
+ *
+ *  - The simplest option is to use a free endstop connector.
+ *  - Use 5V for powered (usually inductive) sensors.
+ *
+ *  - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin:
+ *    - For simple switches connect...
+ *      - normally-closed switches to GND and D32.
+ *      - normally-open switches to 5V and D32.
+ *
+ * WARNING: Setting the wrong pin may have unexpected and potentially
+ * disastrous consequences. Use with caution and do your homework.
+ *
+ */
+//#define Z_MIN_PROBE_ENDSTOP
+
+/**
+ * Probe Type
+ *
+ * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
+ * Activate one of these to use Auto Bed Leveling below.
+ */
+
+/**
+ * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe.
+ * Use G29 repeatedly, adjusting the Z height at each point with movement commands
+ * or (with LCD_BED_LEVELING) the LCD controller.
+ */
+#define PROBE_MANUALLY
+//#define MANUAL_PROBE_START_Z 0.2
+
+/**
+ * A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
+ *   (e.g., an inductive probe or a nozzle-based probe-switch.)
+ */
+//#define FIX_MOUNTED_PROBE
+
+/**
+ * Z Servo Probe, such as an endstop switch on a rotating arm.
+ */
+//#define Z_PROBE_SERVO_NR 0   // Defaults to SERVO 0 connector.
+//#define Z_SERVO_ANGLES {70,0}  // Z Servo Deploy and Stow angles
+
+/**
+ * The BLTouch probe uses a Hall effect sensor and emulates a servo.
+ */
+//#define BLTOUCH
+
+/**
+ * Enable one or more of the following if probing seems unreliable.
+ * Heaters and/or fans can be disabled during probing to minimize electrical
+ * noise. A delay can also be added to allow noise and vibration to settle.
+ * These options are most useful for the BLTouch probe, but may also improve
+ * readings with inductive probes and piezo sensors.
+ */
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
+//#define PROBING_FANS_OFF          // Turn fans off when probing
+//#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
+
+// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
+//#define SOLENOID_PROBE
+
+// A sled-mounted probe like those designed by Charles Bell.
+//#define Z_PROBE_SLED
+//#define SLED_DOCKING_OFFSET 5  // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
+
+//
+// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
+//
+
+/**
+ *   Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+ *   X and Y offsets must be integers.
+ *
+ *   In the following example the X and Y offsets are both positive:
+ *   #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+ *   #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+ *
+ *      +-- BACK ---+
+ *      |           |
+ *    L |    (+) P  | R <-- probe (20,20)
+ *    E |           | I
+ *    F | (-) N (+) | G <-- nozzle (10,10)
+ *    T |           | H
+ *      |    (-)    | T
+ *      |           |
+ *      O-- FRONT --+
+ *    (0,0)
+ */
+#define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
+#define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]
+#define Z_PROBE_OFFSET_FROM_EXTRUDER 0   // Z offset: -below +above  [the nozzle]
+
+// Certain types of probes need to stay away from edges
+#define MIN_PROBE_EDGE 10
+
+// X and Y axis travel speed (mm/m) between probes
+#define XY_PROBE_SPEED 8000
+
+// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
+#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
+
+// Feedrate (mm/m) for the "accurate" probe of each point
+#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
+
+// The number of probes to perform at each point.
+//   Set to 2 for a fast/slow probe, using the second probe result.
+//   Set to 3 or more for slow probes, averaging the results.
+//#define MULTIPLE_PROBING 2
+
+/**
+ * Z probes require clearance when deploying, stowing, and moving between
+ * probe points to avoid hitting the bed and other hardware.
+ * Servo-mounted probes require extra space for the arm to rotate.
+ * Inductive probes need space to keep from triggering early.
+ *
+ * Use these settings to specify the distance (mm) to raise the probe (or
+ * lower the bed). The values set here apply over and above any (negative)
+ * probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD.
+ * Only integer values >= 1 are valid here.
+ *
+ * Example: `M851 Z-5` with a CLEARANCE of 4  =>  9mm from bed to nozzle.
+ *     But: `M851 Z+1` with a CLEARANCE of 2  =>  2mm from bed to nozzle.
+ */
+#define Z_CLEARANCE_DEPLOY_PROBE   10 // Z Clearance for Deploy/Stow
+#define Z_CLEARANCE_BETWEEN_PROBES  5 // Z Clearance between probe points
+#define Z_CLEARANCE_MULTI_PROBE     5 // Z Clearance between multiple probes
+//#define Z_AFTER_PROBING           5 // Z position after probing is done
+
+#define Z_PROBE_LOW_POINT          -2 // Farthest distance below the trigger-point to go before stopping
+
+// For M851 give a range for adjusting the Z probe offset
+#define Z_PROBE_OFFSET_RANGE_MIN -20
+#define Z_PROBE_OFFSET_RANGE_MAX 20
+
+// Enable the M48 repeatability test to test probe accuracy
+//#define Z_MIN_PROBE_REPEATABILITY_TEST
+
+// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
+// :{ 0:'Low', 1:'High' }
+#define X_ENABLE_ON 0
+#define Y_ENABLE_ON 0
+#define Z_ENABLE_ON 0
+#define E_ENABLE_ON 0 // For all extruders
+
+// Disables axis stepper immediately when it's not being used.
+// WARNING: When motors turn off there is a chance of losing position accuracy!
+#define DISABLE_X false
+#define DISABLE_Y false
+#define DISABLE_Z false
+// Warn on display about possibly reduced accuracy
+//#define DISABLE_REDUCED_ACCURACY_WARNING
+
+// @section extruder
+
+#define DISABLE_E false // For all extruders
+#define DISABLE_INACTIVE_EXTRUDER true // Keep only the active extruder enabled.
+
+// @section machine
+
+// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
+#define INVERT_X_DIR false
+#define INVERT_Y_DIR false
+#define INVERT_Z_DIR true
+
+// @section extruder
+
+// For direct drive extruder v9 set to true, for geared extruder set to false.
+#define INVERT_E0_DIR false
+#define INVERT_E1_DIR false
+#define INVERT_E2_DIR false
+#define INVERT_E3_DIR false
+#define INVERT_E4_DIR false
+
+// @section homing
+
+//#define NO_MOTION_BEFORE_HOMING  // Inhibit movement until all axes have been homed
+
+//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
+
+#define Z_HOMING_HEIGHT 4    // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                             // Be sure you have this distance over your Z_MAX_POS in case.
+
+// Direction of endstops when homing; 1=MAX, -1=MIN
+// :[-1,1]
+#define X_HOME_DIR -1
+#define Y_HOME_DIR -1
+#define Z_HOME_DIR -1
+
+// @section machine
+
+// The size of the print bed
+#define X_BED_SIZE 300
+#define Y_BED_SIZE 300
+
+// Travel limits (mm) after homing, corresponding to endstop positions.
+#define X_MIN_POS 0
+#define Y_MIN_POS 0
+#define Z_MIN_POS 0
+#define X_MAX_POS X_BED_SIZE
+#define Y_MAX_POS Y_BED_SIZE
+#define Z_MAX_POS 400
+
+/**
+ * Software Endstops
+ *
+ * - Prevent moves outside the set machine bounds.
+ * - Individual axes can be disabled, if desired.
+ * - X and Y only apply to Cartesian robots.
+ * - Use 'M211' to set software endstops on/off or report current state
+ */
+
+// Min software endstops constrain movement within minimum coordinate bounds
+#define MIN_SOFTWARE_ENDSTOPS
+#if ENABLED(MIN_SOFTWARE_ENDSTOPS)
+  #define MIN_SOFTWARE_ENDSTOP_X
+  #define MIN_SOFTWARE_ENDSTOP_Y
+  #define MIN_SOFTWARE_ENDSTOP_Z
+#endif
+
+// Max software endstops constrain movement within maximum coordinate bounds
+#define MAX_SOFTWARE_ENDSTOPS
+#if ENABLED(MAX_SOFTWARE_ENDSTOPS)
+  #define MAX_SOFTWARE_ENDSTOP_X
+  #define MAX_SOFTWARE_ENDSTOP_Y
+  #define MAX_SOFTWARE_ENDSTOP_Z
+#endif
+
+#if ENABLED(MIN_SOFTWARE_ENDSTOPS) || ENABLED(MAX_SOFTWARE_ENDSTOPS)
+  //#define SOFT_ENDSTOPS_MENU_ITEM  // Enable/Disable software endstops from the LCD
+#endif
+
+/**
+ * Filament Runout Sensors
+ * Mechanical or opto endstops are used to check for the presence of filament.
+ *
+ * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
+ * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
+ * By default the firmware assumes HIGH=FILAMENT PRESENT.
+ */
+#define FILAMENT_RUNOUT_SENSOR
+#if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
+  #define FIL_RUNOUT_INVERTING true // set to true to invert the logic of the sensor.
+  #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
+  #define FILAMENT_RUNOUT_SCRIPT "M600"
+  #define FIL_RUNOUT_PIN 2 // Creality CR10-S stock sensor
+#endif
+
+//===========================================================================
+//=============================== Bed Leveling ==============================
+//===========================================================================
+// @section calibrate
+
+/**
+ * Choose one of the options below to enable G29 Bed Leveling. The parameters
+ * and behavior of G29 will change depending on your selection.
+ *
+ *  If using a Probe for Z Homing, enable Z_SAFE_HOMING also!
+ *
+ * - AUTO_BED_LEVELING_3POINT
+ *   Probe 3 arbitrary points on the bed (that aren't collinear)
+ *   You specify the XY coordinates of all 3 points.
+ *   The result is a single tilted plane. Best for a flat bed.
+ *
+ * - AUTO_BED_LEVELING_LINEAR
+ *   Probe several points in a grid.
+ *   You specify the rectangle and the density of sample points.
+ *   The result is a single tilted plane. Best for a flat bed.
+ *
+ * - AUTO_BED_LEVELING_BILINEAR
+ *   Probe several points in a grid.
+ *   You specify the rectangle and the density of sample points.
+ *   The result is a mesh, best for large or uneven beds.
+ *
+ * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling)
+ *   A comprehensive bed leveling system combining the features and benefits
+ *   of other systems. UBL also includes integrated Mesh Generation, Mesh
+ *   Validation and Mesh Editing systems.
+ *
+ * - MESH_BED_LEVELING
+ *   Probe a grid manually
+ *   The result is a mesh, suitable for large or uneven beds. (See BILINEAR.)
+ *   For machines without a probe, Mesh Bed Leveling provides a method to perform
+ *   leveling in steps so you can manually adjust the Z height at each grid-point.
+ *   With an LCD controller the process is guided step-by-step.
+ */
+//#define AUTO_BED_LEVELING_3POINT
+//#define AUTO_BED_LEVELING_LINEAR
+#define AUTO_BED_LEVELING_BILINEAR
+//#define AUTO_BED_LEVELING_UBL
+//#define MESH_BED_LEVELING
+
+/**
+ * Normally G28 leaves leveling disabled on completion. Enable
+ * this option to have G28 restore the prior leveling state.
+ */
+//#define RESTORE_LEVELING_AFTER_G28
+
+/**
+ * Enable detailed logging of G28, G29, M48, etc.
+ * Turn on with the command 'M111 S32'.
+ * NOTE: Requires a lot of PROGMEM!
+ */
+//#define DEBUG_LEVELING_FEATURE
+
+#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
+  // Gradually reduce leveling correction until a set height is reached,
+  // at which point movement will be level to the machine's XY plane.
+  // The height can be set with M420 Z<height>
+  #define ENABLE_LEVELING_FADE_HEIGHT
+
+  // For Cartesian machines, instead of dividing moves on mesh boundaries,
+  // split up moves into short segments like a Delta. This follows the
+  // contours of the bed more closely than edge-to-edge straight moves.
+  #define SEGMENT_LEVELED_MOVES
+  #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one)
+
+  /**
+   * Enable the G26 Mesh Validation Pattern tool.
+   */
+  #define G26_MESH_VALIDATION   // Enable G26 mesh validation
+  #if ENABLED(G26_MESH_VALIDATION)
+    #define MESH_TEST_NOZZLE_SIZE    0.4  // (mm) Diameter of primary nozzle.
+    #define MESH_TEST_LAYER_HEIGHT   0.2  // (mm) Default layer height for the G26 Mesh Validation Tool.
+    #define MESH_TEST_HOTEND_TEMP  205.0  // (°C) Default nozzle temperature for the G26 Mesh Validation Tool.
+    #define MESH_TEST_BED_TEMP      60.0  // (°C) Default bed temperature for the G26 Mesh Validation Tool.
+  #endif
+
+#endif
+
+#if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR)
+
+  // Set the number of grid points per dimension.
+  #define GRID_MAX_POINTS_X 3
+  #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
+
+  // Set the boundaries for probing (where the probe can reach).
+  //#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
+  //#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - MIN_PROBE_EDGE)
+  //#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
+  //#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - MIN_PROBE_EDGE)
+
+  // Probe along the Y axis, advancing X after each column
+  //#define PROBE_Y_FIRST
+
+  #if ENABLED(AUTO_BED_LEVELING_BILINEAR)
+
+    // Beyond the probed grid, continue the implied tilt?
+    // Default is to maintain the height of the nearest edge.
+    //#define EXTRAPOLATE_BEYOND_GRID
+
+    //
+    // Experimental Subdivision of the grid by Catmull-Rom method.
+    // Synthesizes intermediate points to produce a more detailed mesh.
+    //
+    //#define ABL_BILINEAR_SUBDIVISION
+    #if ENABLED(ABL_BILINEAR_SUBDIVISION)
+      // Number of subdivisions between probe points
+      #define BILINEAR_SUBDIVISIONS 3
+    #endif
+
+  #endif
+
+#elif ENABLED(AUTO_BED_LEVELING_UBL)
+
+  //===========================================================================
+  //========================= Unified Bed Leveling ============================
+  //===========================================================================
+
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
+  #define MESH_INSET 1              // Set Mesh bounds as an inset region of the bed
+  #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
+  #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
+
+  #define UBL_MESH_EDIT_MOVES_Z     // Sophisticated users prefer no movement of nozzle
+  #define UBL_SAVE_ACTIVE_ON_M500   // Save the currently active mesh in the current slot on M500
+
+  //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used
+                                          // as the Z-Height correction value.
+
+#elif ENABLED(MESH_BED_LEVELING)
+
+  //===========================================================================
+  //=================================== Mesh ==================================
+  //===========================================================================
+
+  #define MESH_INSET 10          // Set Mesh bounds as an inset region of the bed
+  #define GRID_MAX_POINTS_X 3    // Don't use more than 7 points per axis, implementation limited.
+  #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
+
+  //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
+
+#endif // BED_LEVELING
+
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#if ENABLED(AUTO_BED_LEVELING_3POINT) || ENABLED(AUTO_BED_LEVELING_UBL)
+  //#define PROBE_PT_1_X 15
+  //#define PROBE_PT_1_Y 180
+  //#define PROBE_PT_2_X 15
+  //#define PROBE_PT_2_Y 20
+  //#define PROBE_PT_3_X 170
+  //#define PROBE_PT_3_Y 20
+#endif
+
+/**
+ * Add a bed leveling sub-menu for ABL or MBL.
+ * Include a guided procedure if manual probing is enabled.
+ */
+#define LCD_BED_LEVELING
+
+#if ENABLED(LCD_BED_LEVELING)
+  #define MBL_Z_STEP 0.025    // Step size while manually probing Z axis.
+  #define LCD_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
+#endif
+
+// Add a menu item to move between bed corners for manual bed adjustment
+#define LEVEL_BED_CORNERS
+
+#if ENABLED(LEVEL_BED_CORNERS)
+  #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
+  #define LEVEL_CORNERS_Z_HOP  4.0  // (mm) Move nozzle up before moving between corners
+  //#define LEVEL_CENTER_TOO        // Move to the center after the last corner
+#endif
+
+/**
+ * Commands to execute at the end of G29 probing.
+ * Useful to retract or move the Z probe out of the way.
+ */
+//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"
+
+
+// @section homing
+
+// The center of the bed is at (X=0, Y=0)
+//#define BED_CENTER_AT_0_0
+
+// Manually set the home position. Leave these undefined for automatic settings.
+// For DELTA this is the top-center of the Cartesian print volume.
+//#define MANUAL_X_HOME_POS 0
+//#define MANUAL_Y_HOME_POS 0
+//#define MANUAL_Z_HOME_POS 0
+
+// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
+//
+// With this feature enabled:
+//
+// - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
+// - If stepper drivers time out, it will need X and Y homing again before Z homing.
+// - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28).
+// - Prevent Z homing when the Z probe is outside bed area.
+//
+//#define Z_SAFE_HOMING
+
+#if ENABLED(Z_SAFE_HOMING)
+  #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2)    // X point for Z homing when homing all axes (G28).
+  #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2)    // Y point for Z homing when homing all axes (G28).
+#endif
+
+// Homing speeds (mm/m)
+#define HOMING_FEEDRATE_XY (20*60)
+#define HOMING_FEEDRATE_Z  (4*60)
+
+// @section calibrate
+
+/**
+ * Bed Skew Compensation
+ *
+ * This feature corrects for misalignment in the XYZ axes.
+ *
+ * Take the following steps to get the bed skew in the XY plane:
+ *  1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185)
+ *  2. For XY_DIAG_AC measure the diagonal A to C
+ *  3. For XY_DIAG_BD measure the diagonal B to D
+ *  4. For XY_SIDE_AD measure the edge A to D
+ *
+ * Marlin automatically computes skew factors from these measurements.
+ * Skew factors may also be computed and set manually:
+ *
+ *  - Compute AB     : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2
+ *  - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD)))
+ *
+ * If desired, follow the same procedure for XZ and YZ.
+ * Use these diagrams for reference:
+ *
+ *    Y                     Z                     Z
+ *    ^     B-------C       ^     B-------C       ^     B-------C
+ *    |    /       /        |    /       /        |    /       /
+ *    |   /       /         |   /       /         |   /       /
+ *    |  A-------D          |  A-------D          |  A-------D
+ *    +-------------->X     +-------------->X     +-------------->Y
+ *     XY_SKEW_FACTOR        XZ_SKEW_FACTOR        YZ_SKEW_FACTOR
+ */
+//#define SKEW_CORRECTION
+
+#if ENABLED(SKEW_CORRECTION)
+  // Input all length measurements here:
+  #define XY_DIAG_AC 282.8427124746
+  #define XY_DIAG_BD 282.8427124746
+  #define XY_SIDE_AD 200
+
+  // Or, set the default skew factors directly here
+  // to override the above measurements:
+  #define XY_SKEW_FACTOR 0.0
+
+  //#define SKEW_CORRECTION_FOR_Z
+  #if ENABLED(SKEW_CORRECTION_FOR_Z)
+    #define XZ_DIAG_AC 282.8427124746
+    #define XZ_DIAG_BD 282.8427124746
+    #define YZ_DIAG_AC 282.8427124746
+    #define YZ_DIAG_BD 282.8427124746
+    #define YZ_SIDE_AD 200
+    #define XZ_SKEW_FACTOR 0.0
+    #define YZ_SKEW_FACTOR 0.0
+  #endif
+
+  // Enable this option for M852 to set skew at runtime
+  //#define SKEW_CORRECTION_GCODE
+#endif
+
+//=============================================================================
+//============================= Additional Features ===========================
+//=============================================================================
+
+// @section extras
+
+//
+// EEPROM
+//
+// The microcontroller can store settings in the EEPROM, e.g. max velocity...
+// M500 - stores parameters in EEPROM
+// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
+// M502 - reverts to the default "factory settings".  You still need to store them in EEPROM afterwards if you want to.
+//
+#define EEPROM_SETTINGS   // Enable for M500 and M501 commands
+//#define DISABLE_M503    // Saves ~2700 bytes of PROGMEM. Disable for release!
+#define EEPROM_CHITCHAT   // Give feedback on EEPROM commands. Disable to save PROGMEM.
+
+//
+// Host Keepalive
+//
+// When enabled Marlin will send a busy status message to the host
+// every couple of seconds when it can't accept commands.
+//
+#define HOST_KEEPALIVE_FEATURE        // Disable this if your host doesn't like keepalive messages
+#define DEFAULT_KEEPALIVE_INTERVAL 2  // Number of seconds between "busy" messages. Set with M113.
+#define BUSY_WHILE_HEATING            // Some hosts require "busy" messages even during heating
+
+//
+// M100 Free Memory Watcher
+//
+//#define M100_FREE_MEMORY_WATCHER    // Add M100 (Free Memory Watcher) to debug memory usage
+
+//
+// G20/G21 Inch mode support
+//
+//#define INCH_MODE_SUPPORT
+
+//
+// M149 Set temperature units support
+//
+//#define TEMPERATURE_UNITS_SUPPORT
+
+// @section temperature
+
+// Preheat Constants
+#define PREHEAT_1_TEMP_HOTEND 205
+#define PREHEAT_1_TEMP_BED     60
+#define PREHEAT_1_FAN_SPEED     0 // Value from 0 to 255
+
+#define PREHEAT_2_TEMP_HOTEND 250
+#define PREHEAT_2_TEMP_BED    80
+#define PREHEAT_2_FAN_SPEED     0 // Value from 0 to 255
+
+/**
+ * Nozzle Park
+ *
+ * Park the nozzle at the given XYZ position on idle or G27.
+ *
+ * The "P" parameter controls the action applied to the Z axis:
+ *
+ *    P0  (Default) If Z is below park Z raise the nozzle.
+ *    P1  Raise the nozzle always to Z-park height.
+ *    P2  Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
+ */
+#define NOZZLE_PARK_FEATURE
+
+#if ENABLED(NOZZLE_PARK_FEATURE)
+  // Specify a park position as { X, Y, Z }
+  #define NOZZLE_PARK_POINT { (X_MIN_POS + 3), (Y_MAX_POS - 3), 10 }
+  #define NOZZLE_PARK_XY_FEEDRATE 100   // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
+  #define NOZZLE_PARK_Z_FEEDRATE 5      // Z axis feedrate in mm/s (not used for delta printers)
+#endif
+
+/**
+ * Clean Nozzle Feature -- EXPERIMENTAL
+ *
+ * Adds the G12 command to perform a nozzle cleaning process.
+ *
+ * Parameters:
+ *   P  Pattern
+ *   S  Strokes / Repetitions
+ *   T  Triangles (P1 only)
+ *
+ * Patterns:
+ *   P0  Straight line (default). This process requires a sponge type material
+ *       at a fixed bed location. "S" specifies strokes (i.e. back-forth motions)
+ *       between the start / end points.
+ *
+ *   P1  Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the
+ *       number of zig-zag triangles to do. "S" defines the number of strokes.
+ *       Zig-zags are done in whichever is the narrower dimension.
+ *       For example, "G12 P1 S1 T3" will execute:
+ *
+ *          --
+ *         |  (X0, Y1) |     /\        /\        /\     | (X1, Y1)
+ *         |           |    /  \      /  \      /  \    |
+ *       A |           |   /    \    /    \    /    \   |
+ *         |           |  /      \  /      \  /      \  |
+ *         |  (X0, Y0) | /        \/        \/        \ | (X1, Y0)
+ *          --         +--------------------------------+
+ *                       |________|_________|_________|
+ *                           T1        T2        T3
+ *
+ *   P2  Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE.
+ *       "R" specifies the radius. "S" specifies the stroke count.
+ *       Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT.
+ *
+ *   Caveats: The ending Z should be the same as starting Z.
+ * Attention: EXPERIMENTAL. G-code arguments may change.
+ *
+ */
+//#define NOZZLE_CLEAN_FEATURE
+
+#if ENABLED(NOZZLE_CLEAN_FEATURE)
+  // Default number of pattern repetitions
+  #define NOZZLE_CLEAN_STROKES  12
+
+  // Default number of triangles
+  #define NOZZLE_CLEAN_TRIANGLES  3
+
+  // Specify positions as { X, Y, Z }
+  #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)}
+  #define NOZZLE_CLEAN_END_POINT   {100, 60, (Z_MIN_POS + 1)}
+
+  // Circular pattern radius
+  #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
+  // Circular pattern circle fragments number
+  #define NOZZLE_CLEAN_CIRCLE_FN 10
+  // Middle point of circle
+  #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
+
+  // Moves the nozzle to the initial position
+  #define NOZZLE_CLEAN_GOBACK
+#endif
+
+/**
+ * Print Job Timer
+ *
+ * Automatically start and stop the print job timer on M104/M109/M190.
+ *
+ *   M104 (hotend, no wait) - high temp = none,        low temp = stop timer
+ *   M109 (hotend, wait)    - high temp = start timer, low temp = stop timer
+ *   M190 (bed, wait)       - high temp = start timer, low temp = none
+ *
+ * The timer can also be controlled with the following commands:
+ *
+ *   M75 - Start the print job timer
+ *   M76 - Pause the print job timer
+ *   M77 - Stop the print job timer
+ */
+#define PRINTJOB_TIMER_AUTOSTART
+
+/**
+ * Print Counter
+ *
+ * Track statistical data such as:
+ *
+ *  - Total print jobs
+ *  - Total successful print jobs
+ *  - Total failed print jobs
+ *  - Total time printing
+ *
+ * View the current statistics with M78.
+ */
+//#define PRINTCOUNTER
+
+//=============================================================================
+//============================= LCD and SD support ============================
+//=============================================================================
+
+// @section lcd
+
+/**
+ * LCD LANGUAGE
+ *
+ * Select the language to display on the LCD. These languages are available:
+ *
+ *    en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, es_utf8,
+ *    eu, fi, fr, fr_utf8, gl, hr, it, kana, kana_utf8, nl, pl, pt,
+ *    pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, tr, uk, zh_CN, zh_TW, test
+ *
+ * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'es_utf8':'Spanish (UTF8)', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', 'test':'TEST' }
+ */
+#define LCD_LANGUAGE en
+
+/**
+ * LCD Character Set
+ *
+ * Note: This option is NOT applicable to Graphical Displays.
+ *
+ * All character-based LCDs provide ASCII plus one of these
+ * language extensions:
+ *
+ *  - JAPANESE ... the most common
+ *  - WESTERN  ... with more accented characters
+ *  - CYRILLIC ... for the Russian language
+ *
+ * To determine the language extension installed on your controller:
+ *
+ *  - Compile and upload with LCD_LANGUAGE set to 'test'
+ *  - Click the controller to view the LCD menu
+ *  - The LCD will display Japanese, Western, or Cyrillic text
+ *
+ * See http://marlinfw.org/docs/development/lcd_language.html
+ *
+ * :['JAPANESE', 'WESTERN', 'CYRILLIC']
+ */
+#define DISPLAY_CHARSET_HD44780 JAPANESE
+
+/**
+ * SD CARD
+ *
+ * SD Card support is disabled by default. If your controller has an SD slot,
+ * you must uncomment the following option or it won't work.
+ *
+ */
+#define SDSUPPORT
+
+/**
+ * SD CARD: SPI SPEED
+ *
+ * Enable one of the following items for a slower SPI transfer speed.
+ * This may be required to resolve "volume init" errors.
+ */
+//#define SPI_SPEED SPI_HALF_SPEED
+//#define SPI_SPEED SPI_QUARTER_SPEED
+//#define SPI_SPEED SPI_EIGHTH_SPEED
+
+/**
+ * SD CARD: ENABLE CRC
+ *
+ * Use CRC checks and retries on the SD communication.
+ */
+//#define SD_CHECK_AND_RETRY
+
+/**
+ * LCD Menu Items
+ *
+ * Disable all menus and only display the Status Screen, or
+ * just remove some extraneous menu items to recover space.
+ */
+//#define NO_LCD_MENUS
+//#define SLIM_LCD_MENUS
+
+//
+// ENCODER SETTINGS
+//
+// This option overrides the default number of encoder pulses needed to
+// produce one step. Should be increased for high-resolution encoders.
+//
+//#define ENCODER_PULSES_PER_STEP 4
+
+//
+// Use this option to override the number of step signals required to
+// move between next/prev menu items.
+//
+//#define ENCODER_STEPS_PER_MENU_ITEM 1
+
+/**
+ * Encoder Direction Options
+ *
+ * Test your encoder's behavior first with both options disabled.
+ *
+ *  Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
+ *  Reversed Menu Navigation only?    Enable REVERSE_MENU_DIRECTION.
+ *  Reversed Value Editing only?      Enable BOTH options.
+ */
+
+//
+// This option reverses the encoder direction everywhere.
+//
+//  Set this option if CLOCKWISE causes values to DECREASE
+//
+//#define REVERSE_ENCODER_DIRECTION
+
+//
+// This option reverses the encoder direction for navigating LCD menus.
+//
+//  If CLOCKWISE normally moves DOWN this makes it go UP.
+//  If CLOCKWISE normally moves UP this makes it go DOWN.
+//
+//#define REVERSE_MENU_DIRECTION
+
+//
+// Individual Axis Homing
+//
+// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
+//
+//#define INDIVIDUAL_AXIS_HOMING_MENU
+
+//
+// SPEAKER/BUZZER
+//
+// If you have a speaker that can produce tones, enable it here.
+// By default Marlin assumes you have a buzzer with a fixed frequency.
+//
+#define SPEAKER
+
+//
+// The duration and frequency for the UI feedback sound.
+// Set these to 0 to disable audio feedback in the LCD menus.
+//
+// Note: Test audio output with the G-Code:
+//  M300 S<frequency Hz> P<duration ms>
+//
+//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2
+//#define LCD_FEEDBACK_FREQUENCY_HZ 5000
+
+//=============================================================================
+//======================== LCD / Controller Selection =========================
+//========================   (Character-based LCDs)   =========================
+//=============================================================================
+
+//
+// RepRapDiscount Smart Controller.
+// http://reprap.org/wiki/RepRapDiscount_Smart_Controller
+//
+// Note: Usually sold with a white PCB.
+//
+//#define REPRAP_DISCOUNT_SMART_CONTROLLER
+
+//
+// ULTIMAKER Controller.
+//
+//#define ULTIMAKERCONTROLLER
+
+//
+// ULTIPANEL as seen on Thingiverse.
+//
+//#define ULTIPANEL
+
+//
+// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
+// http://reprap.org/wiki/PanelOne
+//
+//#define PANEL_ONE
+
+//
+// GADGETS3D G3D LCD/SD Controller
+// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
+//
+// Note: Usually sold with a blue PCB.
+//
+//#define G3D_PANEL
+
+//
+// RigidBot Panel V1.0
+// http://www.inventapart.com/
+//
+//#define RIGIDBOT_PANEL
+
+//
+// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller
+// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html
+//
+//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602
+
+//
+// ANET and Tronxy 20x4 Controller
+//
+//#define ZONESTAR_LCD            // Requires ADC_KEYPAD_PIN to be assigned to an analog pin.
+                                  // This LCD is known to be susceptible to electrical interference
+                                  // which scrambles the display.  Pressing any button clears it up.
+                                  // This is a LCD2004 display with 5 analog buttons.
+
+//
+// Generic 16x2, 16x4, 20x2, or 20x4 character-based LCD.
+//
+//#define ULTRA_LCD
+
+//=============================================================================
+//======================== LCD / Controller Selection =========================
+//=====================   (I2C and Shift-Register LCDs)   =====================
+//=============================================================================
+
+//
+// CONTROLLER TYPE: I2C
+//
+// Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
+// library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
+//
+
+//
+// Elefu RA Board Control Panel
+// http://www.elefu.com/index.php?route=product/product&product_id=53
+//
+//#define RA_CONTROL_PANEL
+
+//
+// Sainsmart (YwRobot) LCD Displays
+//
+// These require F.Malpartida's LiquidCrystal_I2C library
+// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home
+//
+//#define LCD_SAINSMART_I2C_1602
+//#define LCD_SAINSMART_I2C_2004
+
+//
+// Generic LCM1602 LCD adapter
+//
+//#define LCM1602
+
+//
+// PANELOLU2 LCD with status LEDs,
+// separate encoder and click inputs.
+//
+// Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
+// For more info: https://github.com/lincomatic/LiquidTWI2
+//
+// Note: The PANELOLU2 encoder click input can either be directly connected to
+// a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
+//
+//#define LCD_I2C_PANELOLU2
+
+//
+// Panucatt VIKI LCD with status LEDs,
+// integrated click & L/R/U/D buttons, separate encoder inputs.
+//
+//#define LCD_I2C_VIKI
+
+//
+// CONTROLLER TYPE: Shift register panels
+//
+
+//
+// 2 wire Non-latching LCD SR from https://goo.gl/aJJ4sH
+// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
+//
+//#define SAV_3DLCD
+
+//=============================================================================
+//=======================   LCD / Controller Selection  =======================
+//=========================      (Graphical LCDs)      ========================
+//=============================================================================
+
+//
+// CONTROLLER TYPE: Graphical 128x64 (DOGM)
+//
+// IMPORTANT: The U8glib library is required for Graphical Display!
+//            https://github.com/olikraus/U8glib_Arduino
+//
+
+//
+// RepRapDiscount FULL GRAPHIC Smart Controller
+// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
+//
+#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
+
+//
+// ReprapWorld Graphical LCD
+// https://reprapworld.com/?products_details&products_id/1218
+//
+//#define REPRAPWORLD_GRAPHICAL_LCD
+
+//
+// Activate one of these if you have a Panucatt Devices
+// Viki 2.0 or mini Viki with Graphic LCD
+// http://panucatt.com
+//
+//#define VIKI2
+//#define miniVIKI
+
+//
+// MakerLab Mini Panel with graphic
+// controller and SD support - http://reprap.org/wiki/Mini_panel
+//
+//#define MINIPANEL
+
+//
+// MaKr3d Makr-Panel with graphic controller and SD support.
+// http://reprap.org/wiki/MaKr3d_MaKrPanel
+//
+//#define MAKRPANEL
+
+//
+// Adafruit ST7565 Full Graphic Controller.
+// https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
+//
+//#define ELB_FULL_GRAPHIC_CONTROLLER
+
+//
+// BQ LCD Smart Controller shipped by
+// default with the BQ Hephestos 2 and Witbox 2.
+//
+//#define BQ_LCD_SMART_CONTROLLER
+
+//
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// LCD for Melzi Card with Graphical LCD
+//
+//#define LCD_FOR_MELZI
+
+//
+// SSD1306 OLED full graphics generic display
+//
+//#define U8GLIB_SSD1306
+
+//
+// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
+//
+//#define SAV_3DGLCD
+#if ENABLED(SAV_3DGLCD)
+  //#define U8GLIB_SSD1306
+  #define U8GLIB_SH1106
+#endif
+
+//
+// Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder
+// https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1)
+//
+//#define ULTI_CONTROLLER
+
+//
+// TinyBoy2 128x64 OLED / Encoder Panel
+//
+//#define OLED_PANEL_TINYBOY2
+
+//
+// MKS MINI12864 with graphic controller and SD support
+// http://reprap.org/wiki/MKS_MINI_12864
+//
+//#define MKS_MINI_12864
+
+//
+// Factory display for Creality CR-10
+// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html
+//
+// This is RAMPS-compatible using a single 10-pin connector.
+// (For CR-10 owners who want to replace the Melzi Creality board but retain the display)
+//
+//#define CR10_STOCKDISPLAY
+
+//
+// ANET and Tronxy Graphical Controller
+//
+//#define ANET_FULL_GRAPHICS_LCD  // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
+                                  // A clone of the RepRapDiscount full graphics display but with
+                                  // different pins/wiring (see pins_ANET_10.h).
+
+//
+// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER
+// http://reprap.org/wiki/MKS_12864OLED
+//
+// Tiny, but very sharp OLED display
+//
+//#define MKS_12864OLED          // Uses the SH1106 controller (default)
+//#define MKS_12864OLED_SSD1306  // Uses the SSD1306 controller
+
+//
+// Silvergate GLCD controller
+// http://github.com/android444/Silvergate
+//
+//#define SILVER_GATE_GLCD_CONTROLLER
+
+//=============================================================================
+//============================  Other Controllers  ============================
+//=============================================================================
+
+//
+// CONTROLLER TYPE: Standalone / Serial
+//
+
+//
+// LCD for Malyan M200 printers.
+// This requires SDSUPPORT to be enabled
+//
+//#define MALYAN_LCD
+
+//
+// CONTROLLER TYPE: Keypad / Add-on
+//
+
+//
+// RepRapWorld REPRAPWORLD_KEYPAD v1.1
+// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
+//
+// REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key
+// is pressed, a value of 10.0 means 10mm per click.
+//
+//#define REPRAPWORLD_KEYPAD
+//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0
+
+//=============================================================================
+//=============================== Extra Features ==============================
+//=============================================================================
+
+// @section extras
+
+// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
+//#define FAST_PWM_FAN
+
+// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
+// which is not as annoying as with the hardware PWM. On the other hand, if this frequency
+// is too low, you should also increment SOFT_PWM_SCALE.
+//#define FAN_SOFT_PWM
+
+// Incrementing this by 1 will double the software PWM frequency,
+// affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
+// However, control resolution will be halved for each increment;
+// at zero value, there are 128 effective control positions.
+#define SOFT_PWM_SCALE 0
+
+// If SOFT_PWM_SCALE is set to a value higher than 0, dithering can
+// be used to mitigate the associated resolution loss. If enabled,
+// some of the PWM cycles are stretched so on average the desired
+// duty cycle is attained.
+//#define SOFT_PWM_DITHER
+
+// Temperature status LEDs that display the hotend and bed temperature.
+// If all hotends, bed temperature, and target temperature are under 54C
+// then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis)
+//#define TEMP_STAT_LEDS
+
+// M240  Triggers a camera by emulating a Canon RC-1 Remote
+// Data from: http://www.doc-diy.net/photo/rc-1_hacked/
+//#define PHOTOGRAPH_PIN     23
+
+// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
+//#define SF_ARC_FIX
+
+// Support for the BariCUDA Paste Extruder
+//#define BARICUDA
+
+// Support for BlinkM/CyzRgb
+//#define BLINKM
+
+// Support for PCA9632 PWM LED driver
+//#define PCA9632
+
+/**
+ * RGB LED / LED Strip Control
+ *
+ * Enable support for an RGB LED connected to 5V digital pins, or
+ * an RGB Strip connected to MOSFETs controlled by digital pins.
+ *
+ * Adds the M150 command to set the LED (or LED strip) color.
+ * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
+ * luminance values can be set from 0 to 255.
+ * For Neopixel LED an overall brightness parameter is also available.
+ *
+ * *** CAUTION ***
+ *  LED Strips require a MOSFET Chip between PWM lines and LEDs,
+ *  as the Arduino cannot handle the current the LEDs will require.
+ *  Failure to follow this precaution can destroy your Arduino!
+ *  NOTE: A separate 5V power supply is required! The Neopixel LED needs
+ *  more current than the Arduino 5V linear regulator can produce.
+ * *** CAUTION ***
+ *
+ * LED Type. Enable only one of the following two options.
+ *
+ */
+//#define RGB_LED
+//#define RGBW_LED
+
+#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
+  #define RGB_LED_R_PIN 34
+  #define RGB_LED_G_PIN 43
+  #define RGB_LED_B_PIN 35
+  #define RGB_LED_W_PIN -1
+#endif
+
+// Support for Adafruit Neopixel LED driver
+//#define NEOPIXEL_LED
+#if ENABLED(NEOPIXEL_LED)
+  #define NEOPIXEL_TYPE   NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
+  #define NEOPIXEL_PIN    4        // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs in the strip
+  #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
+  #define NEOPIXEL_BRIGHTNESS 127  // Initial brightness (0-255)
+  //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
+#endif
+
+/**
+ * Printer Event LEDs
+ *
+ * During printing, the LEDs will reflect the printer status:
+ *
+ *  - Gradually change from blue to violet as the heated bed gets to target temp
+ *  - Gradually change from violet to red as the hotend gets to temperature
+ *  - Change to white to illuminate work surface
+ *  - Change to green once print has finished
+ *  - Turn off after the print has finished and the user has pushed a button
+ */
+#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
+  #define PRINTER_EVENT_LEDS
+#endif
+
+/**
+ * R/C SERVO support
+ * Sponsored by TrinityLabs, Reworked by codexmas
+ */
+
+/**
+ * Number of servos
+ *
+ * For some servo-related options NUM_SERVOS will be set automatically.
+ * Set this manually if there are extra servos needing manual control.
+ * Leave undefined or set to 0 to entirely disable the servo subsystem.
+ */
+//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
+
+// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// 300ms is a good value but you can try less delay.
+// If the servo can't reach the requested position, increase it.
+#define SERVO_DELAY { 300 }
+
+// Only power servos during movement, otherwise leave off to prevent jitter
+//#define DEACTIVATE_SERVOS_AFTER_MOVE
+
+#endif // CONFIGURATION_H