diff options
| -rw-r--r-- | marlinfw/config-1.1.x/Configuration.h | 10 | ||||
| -rw-r--r-- | marlinfw/config-1.1.x/Configuration_adv.h | 4 |
2 files changed, 7 insertions, 7 deletions
diff --git a/marlinfw/config-1.1.x/Configuration.h b/marlinfw/config-1.1.x/Configuration.h index 37b4c2a..b85a5a0 100644 --- a/marlinfw/config-1.1.x/Configuration.h +++ b/marlinfw/config-1.1.x/Configuration.h @@ -713,7 +713,7 @@ * Use G29 repeatedly, adjusting the Z height at each point with movement commands * or (with LCD_BED_LEVELING) the LCD controller. */ -#define PROBE_MANUALLY +//#define PROBE_MANUALLY //#define MANUAL_PROBE_START_Z 0.2 /** @@ -731,7 +731,7 @@ /** * The BLTouch probe uses a Hall effect sensor and emulates a servo. */ -//#define BLTOUCH +#define BLTOUCH /** * Enable one or more of the following if probing seems unreliable. @@ -777,8 +777,8 @@ * O-- FRONT --+ * (0,0) */ -#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle] -#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle] +#define X_PROBE_OFFSET_FROM_EXTRUDER -45 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER -9 // Y offset: -front +behind [the nozzle] #define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle] // Certain types of probes need to stay away from edges @@ -1144,7 +1144,7 @@ // - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28). // - Prevent Z homing when the Z probe is outside bed area. // -//#define Z_SAFE_HOMING +#define Z_SAFE_HOMING #if ENABLED(Z_SAFE_HOMING) #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28). diff --git a/marlinfw/config-1.1.x/Configuration_adv.h b/marlinfw/config-1.1.x/Configuration_adv.h index 9ae8a59..67dc5e7 100644 --- a/marlinfw/config-1.1.x/Configuration_adv.h +++ b/marlinfw/config-1.1.x/Configuration_adv.h @@ -808,11 +808,11 @@ //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA! #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way #define BABYSTEP_MULTIPLICATOR 5 // Babysteps are very small. Increase for faster motion. - //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping + #define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping #define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping. #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds. // Note: Extra time may be added to mitigate controller latency. - //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor + #define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor #endif // @section extruder |