diff options
Diffstat (limited to 'marlinfw-skr-e3-mini-v2')
| -rw-r--r-- | marlinfw-skr-e3-mini-v2/config-2.0.9.2/Configuration.h | 16 | ||||
| -rw-r--r-- | marlinfw-skr-e3-mini-v2/config-2.0.9.2/Configuration_adv.h | 12 |
2 files changed, 14 insertions, 14 deletions
diff --git a/marlinfw-skr-e3-mini-v2/config-2.0.9.2/Configuration.h b/marlinfw-skr-e3-mini-v2/config-2.0.9.2/Configuration.h index 4bdc3da..2d06579 100644 --- a/marlinfw-skr-e3-mini-v2/config-2.0.9.2/Configuration.h +++ b/marlinfw-skr-e3-mini-v2/config-2.0.9.2/Configuration.h @@ -1090,7 +1090,7 @@ /** * The BLTouch probe uses a Hall effect sensor and emulates a servo. */ -//#define BLTOUCH +#define BLTOUCH /** * Touch-MI Probe by hotends.fr @@ -1182,11 +1182,11 @@ * | [-] | * O-- FRONT --+ */ -#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 } +#define NOZZLE_TO_PROBE_OFFSET { -43, -10, 0 } // Z-offset usally -2.58 // Most probes should stay away from the edges of the bed, but // with NOZZLE_AS_PROBE this can be negative for a wider probing area. -#define PROBING_MARGIN 10 +#define PROBING_MARGIN 40 // X and Y axis travel speed (mm/min) between probes #define XY_PROBE_FEEDRATE (133*60) @@ -1233,7 +1233,7 @@ * A total of 2 does fast/slow probes with a weighted average. * A total of 3 or more adds more slow probes, taking the average. */ -//#define MULTIPLE_PROBING 2 +#define MULTIPLE_PROBING 2 //#define EXTRA_PROBING 1 /** @@ -1539,9 +1539,9 @@ */ //#define AUTO_BED_LEVELING_3POINT //#define AUTO_BED_LEVELING_LINEAR -//#define AUTO_BED_LEVELING_BILINEAR +#define AUTO_BED_LEVELING_BILINEAR //#define AUTO_BED_LEVELING_UBL -#define MESH_BED_LEVELING +//#define MESH_BED_LEVELING /** * Normally G28 leaves leveling disabled on completion. Enable one of @@ -1606,7 +1606,7 @@ #if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR) // Set the number of grid points per dimension. - #define GRID_MAX_POINTS_X 5 + #define GRID_MAX_POINTS_X 9 #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X // Probe along the Y axis, advancing X after each column @@ -1740,7 +1740,7 @@ * - Allows Z homing only when XY positions are known and trusted. * - If stepper drivers sleep, XY homing may be required again before Z homing. */ -//#define Z_SAFE_HOMING +#define Z_SAFE_HOMING #if ENABLED(Z_SAFE_HOMING) #define Z_SAFE_HOMING_X_POINT X_CENTER // X point for Z homing diff --git a/marlinfw-skr-e3-mini-v2/config-2.0.9.2/Configuration_adv.h b/marlinfw-skr-e3-mini-v2/config-2.0.9.2/Configuration_adv.h index 4c9224c..5227362 100644 --- a/marlinfw-skr-e3-mini-v2/config-2.0.9.2/Configuration_adv.h +++ b/marlinfw-skr-e3-mini-v2/config-2.0.9.2/Configuration_adv.h @@ -818,7 +818,7 @@ // Safety: The probe needs time to recognize the command. // Minimum command delay (ms). Enable and increase if needed. - //#define BLTOUCH_DELAY 500 + #define BLTOUCH_DELAY 500 /** * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones: @@ -826,7 +826,7 @@ // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful // in special cases, like noisy or filtered input configurations. - //#define BLTOUCH_FORCE_SW_MODE + #define BLTOUCH_FORCE_SW_MODE /** * Settings for BLTouch Smart 3.0 and 3.1 @@ -1225,14 +1225,14 @@ // Add Probe Z Offset calibration to the Z Probe Offsets menu #if HAS_BED_PROBE - //#define PROBE_OFFSET_WIZARD + #define PROBE_OFFSET_WIZARD #if ENABLED(PROBE_OFFSET_WIZARD) // // Enable to init the Probe Z-Offset when starting the Wizard. // Use a height slightly above the estimated nozzle-to-probe Z offset. // For example, with an offset of -5, consider a starting height of -4. // - //#define PROBE_OFFSET_WIZARD_START_Z -4.0 + #define PROBE_OFFSET_WIZARD_START_Z -2.0 // Set a convenient position to do the calibration (probing point and nozzle/bed-distance) //#define PROBE_OFFSET_WIZARD_XY_POS { X_CENTER, Y_CENTER } @@ -1883,9 +1883,9 @@ #endif #endif - //#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28 + #define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28 - //#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping + #define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping #if ENABLED(BABYSTEP_ZPROBE_OFFSET) //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor |